Browsed by
Category: 3D Printing

RJ45 Ethernet Cover

RJ45 Ethernet Cover

Comments 0 Comment

I am working on a project and I needed an easy way to create an Ethernet jack from a standard patch cable. I found these cheap RJ45 Keystone Adapters (https://www.ebay.ie/itm/RJ45-Keystone-Jack-Wall-End-Plug-Cat-5e-Ethernet-LAN-Network-Module-Port-Adapter/252314420824) which you can easily wire to a standard Ethernet cable. I needed a way to cover the exposed connections and attach it to the project so I designed a cover for them. The jack has to be slightly modified in order to fit into my design, two clips have to…

Read More Read More

Power Supply Cover

Power Supply Cover

Comments 0 Comment

I am using a power supply from Amazon for a project that Im working on and I dont like the cover that they have for preventing people from touching the contacts so I decided to 3D print a new one. I wanted something minimalist that could be easily removed so I designed the following in Solidworks. And then printed it on my ANET A8 3D printer. Then I fit it into the power supply. If you would like to print…

Read More Read More

Hozelock Submersible Water Butt Pump Filter

Hozelock Submersible Water Butt Pump Filter

Comments 0 Comment

The filter on the pump I was using was too fine so I designed a coarser one to replace it. I designed the new filter in SolidWorks. The final print can be seen below: The new filter installed in the pump can be seen below: The files for this model can be found on Thingiverse here.   As always if you have any questions please don’t hesitate to ask, Conor.

ANET A8 Side Filament Guide

ANET A8 Side Filament Guide

Comments 0 Comment

If a roll of filament is new or a print is very wide or tall your filament is more likely to get stuck in the spool holder. This caused one of my prints to fail because the filament got tangled and jammed in the holder and the printer pulled the roll into itself. I designed this guide to go on top of the printer to guide the filament down to the extruder. The guide uses the bolt from rod guard…

Read More Read More

Outside Light Spacer for Garden Power

Outside Light Spacer for Garden Power

Comments 0 Comment

I needed to run a wire from inside an external light to outside it to temporarily get power into my garden. I needed to print a large hexagon the same size and shape as the top of the light shown below but with a gap for the wire to get through. But this shape was larger than the bed on my 3D printer. So I designed the print in 3 parts. The parts are joined with cross-halving joints that will…

Read More Read More

Recover a Print After a Power Cut

Recover a Print After a Power Cut

Comments 0 Comment

I recently did my largest print ever which was expected to take 26 hours! But after about 16 hours there was a power cut and the printer stopped and lost all of its progress. In this post I will got through how I managed to recover the print and allow it continue. The power went during the night so I found the printer after about 4 hours of being off. The first problem was that the nozzle was stuck to…

Read More Read More

Repair By 3D Printing: SD Card Reader

Repair By 3D Printing: SD Card Reader

Comments 0 Comment

I dropped an SD Card reader while a card was in it and broke the card slot. The electronics were fine it but the enclosure that held the card had broken. I’ve highlighted in the picture below what broke. The enclosure that holds the card onto the pins cracked and would no longer hold a card. I thought I’d share the process I went through to fix this. In SolidWorks I drew a cuboid a bit bigger than the size…

Read More Read More

3D Printable Joints

3D Printable Joints

Comments 0 Comment

I am working on a project that requires a large print that won’t fit on my print bed so I will have to print it in 2 parts. I was experimenting with different types of joints to join these two parts. The first was a press fit style of joint. The air gap was 0.2mm between the two parts on this print. This finger style joint had a 0.4mm air gap between the two parts on this print. This dovetail style…

Read More Read More

Model a Hinge in SolidWorks for 3D Printing

Model a Hinge in SolidWorks for 3D Printing

Comments 5 comments

I have created a video tutorial about how to model a print in place Hinge in SolidWorks for 3D printing. The finished model can be seen below: The full tutorial can be seen below (26 minutes), this goes into the full detail of how the SolidWorks was done: I have also created a shortened version (6.5 minutes), which only contains a time lapse and a quick overview of the SolidWorks modelling: The files are available on Thingiverse here.   As…

Read More Read More

Model threads in SolidWorks for 3D Printing

Model threads in SolidWorks for 3D Printing

Comments 0 Comment

I have created a video tutorial about how to model threads in SolidWorks for 3D printing. The finished model can be seen below: The model consists of a main box: And a threaded cap: That thread together: The full tutorial can be seen below (32 minutes), this goes into the full detail of how the SolidWorks was done: I have also created a shortened version (8 minutes), which only contains a time lapse and a quick overview of the SolidWorks…

Read More Read More